Hobbycraft 1/32 P-51A Mustang "Air Commando", by Bill Koppos

               History of the P-51 Mustang? You've seen that before. The story of the First Air Commando, and the early Mustangs the fighter unit flew, is less well-known. Every story has a beginning, and before there were hordes of silvery bubble-topped P-51D's sweeping the skies, a small group of recycled training P-51A's were in down-and-dirty action over the green hell of Burma.

               The first Air Commando Group 's history is integral with that of Wingate's "Chindits", a British army unit organized by one Orde Wingate, an unorthodox type who's specialty was behind- the -lines raiding and infiltration. His ideas were based on groups of troops getting behind the enemy lines, and operating as self-sufficiently as possible, including by airlifts. His first attempt at this in Burma in 1943 failed due to insufficient air support, and for his next try, the politically connected Wingate pulled strings all the way back to Winston Churchill and managed to get an entire air group assigned to his command. This was the beginning of the First Air Commando. (From here on I'll call it the 1st AC). This was organized as a unit to be in support of the ground troops all the way. It included transports, gliders, bombers, fighters, light planes, and even the first helicopters in use in combat anywhere. The object was to insert the troops, supply them thereafter, and be able to evacuate wounded quickly. The fighter component would protect the transports and bombers and do some bombing themselves.

                To command this outfit experience was needed. It was found in the form of Colonel Philip Cochrane, an extremely talented pilot and leader. Col. Cochrane had already found action at the head of an ad hoc P-40 unit in North Africa flying from a behind-the-lines airfield in Tunisia. He had managed to down two Nazi planes and cause them all kinds of trouble. The way he handled his flying and his squadron just added to the material used by Milton Caniff in drawing the "Terry and the Pirates" comic strip, with it's character "Flip Corkin", of course based on Cochrane. Serving as his lieutenant was John Alison, he formerly of the 23rd FG, descendants of the "Flying Tigers", where in China he became an "Ace". Other former "Tigers" were in this outfit, like R.T. Smith, Bob Petit, and Arvid Olsen. As if this weren't enough Grant Mahoney was here to, an aggressive veteran of the Philippines and Java. Expertise would not be in short supply.

              Airplanes, however, were in short supply, with fronts all over making their demands. Fighters for the 1stACG were found in Florida, on training fields.30 well-used P-51A Mustangs were sent to India, presumably because these Allison-engined machines were suitable for the low-level close support mission, while still possessing good range and performance. Range would be critical in the Burma area, as distances were long and the troops to be supported would be behind enemy lines. The P-51A was good here to begin with, helped by the ability to carry under wing drop tanks. Men and machines bought together, it was time for action.

              1st ACG's premier mission was on Valentine's Day 1944, when 13 P-51's led by Cochrane escorted B-25's to attack Japanese installations at a place called Zaundaing. While strafing the target, the ACG fighters were "bounced' by the old Burma hands of the 50th Sentai, flying Ki43 Hayabusas. The ACG was taught a lesson by these veterans, as 2 Mustangs went down and 3 were damaged. It was a harsh introduction to combat. Phil Cochrane was forbidden by Orde Wingate himself from flying again, as his loss could not be afforded. Things improved in the following weeks as missions were flown and experience gained. Most of these were flown against Japanese airfields to soften up opposition to "Thursday", the big airdrop/glider operation behind the enemy lines. This occured on March 5, 1944.

                 The target: two clearings in the jungle coded "Broadway" and "Chowringee". 1st Acg C-47's towed 2 gliders apiece into these areas, where landing strips were quickly built. Over the next 3 days nearly 600 transports landed troops and supplies, which struck out into the jungle to cause the Japanese grief. In the ensuing weeks detachments of 1st ACG mustangs were based at Broadway as were some RAF Spitfires. 3 Japanese Sentais were in the area, and the radar set had limited range, making things rather dangerous. Attacks on the Japanese airfields were frequently made to keep their planes grounded. On 8 March Grant Mahoney led a strike to Aniskan, where several Ki-43's were destroyed in air and on the field. The P-51's returned via the Japanese airfield at Shwebo, diving to attack many aircraft seen there. Lt. Herbert Krug shot up 6 alone, and others downed more. All through March and April the 1st ACG was very active, beating up the JAAF bases while keeping their heads down during enemy fighter sweeps, and supporting the Chindit columns. A tactic taken from Phil Cochrane's time in Tunisia was used. A weight was tied to a cable, and trailed from the P-51's tail. This was flown low over enemy communications lines, ripping them out. "Bazooka" type rocket tubes were used here with some success on airfield attacks. There were losses, too. Lt Krug and 3 others were caught taking off on March 16th by the 50th Sentai, and Krug was hit and burned, being sent stateside.

                 Things turned bad on 24th March. Orde Wingate was flying in a B-25 when it hit bad weather and crashed, the Chindit leader being killed. His replacement was a conservative soldier, and the mission lost it's driving spirit. The campaign ground on, the airfield attacks being the main item. On 4th April several kills were scored in air and enough on the ground that the 50th Sentai had to be sent back to Saigon for re-equipment. On April 17th, Grant Mahoney got his elusive 5th "kill" to reach acedom. It had been a long road from the Philippines for this unflappable, motivated pilot.

                   The grind continued into May. The small number of P-51A's were wearing out, and so were the flyers, and missions were fewer. 19 May proved to be their last day of operations. A pilot was lost, but Lt. Jack Klarr bagged a Ki-43. In the afternoon a bombing raid was their 230th and last mission, as they were withdrawn for "re-organization". The 1st ACG's striped fighters had 10 air kills, with many many others destroyed on airfields. Burma was tough on men and machines, the constant heat and humidity, storms out of nowhere, and forbidding jungle making it one horrendous battleground. The 1st ACG had done one hell of a job.

THE KIT

                 I originally delayed buying this model because there were no decals in the box, nor in the A-36 issue my LHS had either. After a 2-week wait the LHS owner had the decals so I took it home. (The A-36 is still there if anybody wants it). The box is large, cheap corrugated cardboard of the PIA side opening type. The painting/decal charts are on the box bottom, one for our 1st ACG, the other a postwar Dominican Republic A/C, colorful with large numbers if anyone likes that. 5 sprues are there, one being the well-done clear parts. Drop tanks and bazooka type rocket launchers are provided, both of which the 1st ACG planes used. There are two prop types, and flattened or regular tires. The fuselage has a separate nose area, must be B/C versions coming.

                 The plastic used is a soft type, which is good because it makes cleaning up the large sprue attachment points easier. There is an overall "Pebbly" texture to the surfaces, I've heard it called "Matte" but it is kind of rough and never entirely disappears under paint. Panel line and rivet engraving is fine enough. I've heard from several sources, and do believe, that this kit is the Accurate Miniatures 1/48 model scaled up. So if you've done one of those and liked it, you will like this one. Anyway let's get out the sprue cutters and get gluing.

CONSTRUCTION

                 I started with attaching the fuselage fronts to their respective halves. Fit here was very good and the parting line on a panel line, no filling or sanding required.(Hello,Hasegawa? got that?) Upon test fitting the fuse halves I found the rudder to be thick at the trailing edge. A couple of minutes on the table top with 180 grit sandpaper fixed that. Now on to cockpit assembly. At this point let me say I am NO Mustang expert. P-40's and Buffaloes I can help you with, but there are many others out there more qualified to tell you which cockpit floor is right, what color it is, etc. My main object in doing this kit was to try and reproduce the weathered, streaky look of the box art plane, based on a well-known photo. So Mustang boffins, please be gentle with me.

The interior provided is OK, enough detail to look busy when painted, but the aftermarket people could do well here. 2 seats are on the sprues, I used the one indicated in the plan. based on internet refs, admittedly restorations, I painted the cockpit a base of zinc chromate green, with black and aluminum details, and red/white knobs/switches. The instrument panel provided is nicely detailed and takes drybrushing nicely. The tiny box that tells you the cockpit colors says to do the seat "decals over black". Huh? I could not locate any seat belt decals, so this mystery was not solved. I've seen better English on Japanese instruction sheets.

I resorted to an aluminum seat a la P-40's. Would a little more information in this area hurt, Hobbycraft? I'm also still trying to figure out the "twisted arrow" marking that appears several times. No explanation is given at all. Nothing like a little mystery with your modeling. Before sticking the fuselage halves together one must fill the machine gun apertures in the lower nose area, which are used on the A-36 and Brits, but not our P-51A. I just stuck some scrap styrene in the holes, let dry overnight, sand and smooth. Install the tail wheel strut and rear radiator flap, and begin to juggle the cockpit parts into place. The locators are a bit sloppy but go slow and all will fit. When together the fuselage requires minimal seam sanding.

                Upon test fitting the wing halves, I saw the machine gun holes were a little large and even on the leading edge. This ain't right, as the outers are supposed to be lower than the inners. I decided to fix this, so I filled the upper outers with styrene, and shaped the bottom holes to look right. I also shrunk the inners a bit with CA glue and sanding. It definitely looked better. At this point styrene strips were installed to make the gun tubes easy to put in later, and the wings were stuck together. Fitting wing to fuselage, all was well except the front tab area/fuselage, which required more styrene strip to fill large gaps on both sides. The lower radiator scoop was next, attaching this leaves a step that needs lots of CA filling/sanding to achieve a smooth transition. Both the air intake nose scoop and one-piece stabilizers left gaps that needed filling. Finally all was smooth and the dust vacuumed, the cockpit aperture masked, and it was time to repair to the paint room.

COLORS AND MARKINGS

                For many years I had seen in various places a photo taken in 1944. It shows 2 1stACG P-51A's flying above Burma's hills. The foremost aircraft being "Miss Virginia", flown mostly by one Bob Petit, and in the background is our subject, plane no.1. Both machines are extremely weathered, heavy exhaust staining being prominent, and many streaks down the sides messing up the star insignias. Supposedly this was the Mustang flown by Commander Cochrane, and since he ended up flying one mission, one would guess by many others, perhaps second in command Alison? At any rate, I always wanted to try and reproduce this messy look and here was my chance.

                 Examining the photo one notices the exhaust staining is very light, almost white. This has been attributed to the extremely lean fuel mixes these Allison engines were flown on, to stretch the range, combined with the lead in the gas itself. As to the streaks, I always thought this was melted paint washed down by rain. Then while driving one day, I passed a diesel rig. under it's exhaust were black streaks, looking very familiar. Thinking about this and other times I had seen it, I realized this effect was from small soot particles blowing out of the exhaust pipe, then settling on the damp surface below, any wind and water making a streak. At least this explanation satisfied me. Another thing I noticed was at the time the photo was taken, the white ACG stripes were painted OVER these streaks, and the yellow side serial numbers. I can only guess these planes came from Miami in this condition and not even cleaned up before the stripes were applied. Talk about ridden hard and put away wet!

                  At any rate I began to plan how to reproduce all this. Obviously a coat of Olive Drab/Neutral Gray was needed, first things first. I wiped the model down with alcohol first to get rid of my greasy handprints and shot the N/G unders. I always add a touch of white to my paints for "scale effect". Neutral gray as it comes from the Testor's Model Master jar seems a little dark to me. MM Olive Drab was used on top, sprayed freehand as carefully as possible for a tight line on the Gray. I added some more white, and sprayed the centers of some panels, mostly upper ones, to fade the paint in the Burma sun. Then I used a mix with a drop of black to do the upper panel lines, and some random patches here and there for a messy "used" effect. I then glosscoated the model with Testor's Metallizer Sealer, and started applying decals. I was a little worried about my better late than never decals, as they looked kind of thick, but they turned out to be fine, settling with a light coat of Solvaset Decal Solution. The panel lines were rather deep, so I ended up cutting along these to get the decals to settle into them ,a little more Solvaset being applied. T

The U.S. stars/bars come in separate pieces, the round stars being placed on top of the bars. This left a little white around the edges, needing touch up. This didn't matter on the fuselage, as we're going to mess up these decals now. At this stage I had to plan the exhaust stain/stripe matter. As I had determined the stripes were painted OVER the staining and around the stars. Now was time for the stains. The Cochrane plane, no.1, was not as stained as the Miss Virginia one, so I added some White to the regular Olive Drab until it was quite light, and made it a thin mixture. Spraying from exhaust to the back I built up the staining in a curved pattern, over the lower half of the stars, until I judged it enough. Now for the best part. I mixed up some Olive Drab "Sludge"-MM Acrylic OD, water and dish soap, darkened with a drop of black. Working with the reference pic and a fine brush, the soot stains were streaked on over the exhaust stains and decals. The beauty of water wash is if you mess up, you can remove it and redo it. A spit dampened finger does this perfectly. I streaked and fiddled till I had what I wanted, it even looked like the photo a bit! It was even embellished a bit by streaking it forward of the cockpit area as seen in other pics of worn CBI aircraft. I put the serials on, and so far so good.

At this point it was decided to use the decal stripes provided. It would have looked good with painted stripes but I could not risk pulling up the decals with the loads of masking tape that would be used. The other decals had performed well so I began to stripe the 'Stang. Matching the angles to the photo, I worked from front to back, from the center of the fuselage spine, trimming along the center line and around decals with a new #11 blade, and ending short of the bottom center line. I could find no shots of the undersides of these planes, so I assumed the crews would stop short of crawling around under the low-to-the ground Mustang. After all this the rudder stripes were a piece of cake. It all worked out pretty well and there were a couple of stripe pieces left over. Whew!

FINAL BITS

                 The rest of the little decals went on, the red wing root warnings are not the right angle, so were cut and straightened. The landing gear is simple just doors struts and wheels. I chose the flattened (not bulged) wheels. The molded tread is weak and once the seam is sanded, are very bald, like many CBI tires. They also look too square, aftermarkets are needed here. The struts have tabs on the mounting pins with no matching slots on the wing, so these were cut off, and the too long pins trimmed down till fit was correct. I have been told that P-51A's have locks on their inner gear doors and do not droop when parked, so mine were painted and glued "up". Fit was fine. I chose the "paddle bladed" propeller based on the pictures.

The stabilizer tips, rudder tip and spinner were aluminum in the 1st ACG, these were masked and painted. The spinner appears too slim in profile but I didn't go nuts fixing it. Another resin bit is needed. The gun sight provided is a strange thing, I made my own from plastic bits and acetate. For once I decided to have a closed canopy. It was fairly clear, and the plane looked better with it's lines undisturbed. So it was duly masked along with the windscreen and rear windows and given its inside/outside colors. Upon trying to put it on, imagine my shock when I encountered a problem! (I always screw up canopies). This one was too narrow for the fuselage, about an eighth of an inch. How to spread it out without fouling it up? I held the bottom edges apart as much as I dared, and held the top next to a light bulb. Believe it or not, I got away with it (singed fingers and all) with just a hint of crazing in the clear canopy. It had widened just enough to look right. Yay.

                Both antenna posts given were wrong according to pics so I made one out of sprue, and installed nylon thread wires. I cut brass tubing guns to fit and armed the 'Stang. The landing light lens needed just a touch of fiddling to fit, lights and lenses were painted, and I had an Air Commando Pony ready to ride.

CONCLUSIONS

                Not a bad build, it was punctuated by small annoyances here and there. The basic kit is very raw material for a Mustang person who wants to detail it, if some aftermarket stuff comes around. It really could use some wheel, cockpit and spinner improvements. It might have been interesting to put those "Bazooka" rocket tubes on it, as these were used in Burma frequently. I'm thinking about that A-36 that's still sitting on the LHS shelf......

REFERENCES

--Air War for Burma Christopher Shores Grub Street 2005
--Mustang and Thunderbolt Aces of WW2 Osprey Aircraft Of the Aces 26 John Stanaway 1999
--US Army Air Force Fighters Part 2 WW2   Aircraft Fact Files Green and Swanborough 1978

KIT #:	HC 1712
PRICE:	$43.15
DECALS:	Two options
REVIEWER:	Bill Koppos
NOTES:	Check box for decals first. Mine were missing.