Eduard provides their Profipak kit of the later marks of the P-51D with VLR fuel tanks. See Da Boss's preview of the early Mustang.

The main difference is that this special offering comes with the larger fuel tanks including P-38 style fuel tanks used on VLR missions, the different antenna used and 12 different markings used by Iwo Jima P-51Ds as well as the D-20/25 fuselage with the later fin fillet.

It all began with the wheel well. I cleaned up each interior wheel well part to remove the sprue nubs the best I could. Each part was painted as per instructions (I used a 50/50 mix of Tamiya Yellow Green and Flat Yellow for the Chromate Yellow.) The wheel well parts were then glued together and added to the bottom wing piece. The upper wings were glued on with CA glue along the outer seams and Tamiya extra thin along the interior. Next I added the gun sections of both wings. The edges of the wings were sanded smooth using 220/400/600 wet/dry sandpaper till they were relatively smooth and the seam was solid. I polished them further with 1800/3200/3600/4000 grit polishing cloths to remove most of the big scratches. Next I did the same (CA glue for the exterior seams, sanding, polishing) for the ailerons.

The interior parts were painted using Mission Model US interior green while the seat was painted dark green. I selected the blank IP panel and used the Photo-etched IP and details. Next I took what PE parts I figured would be seen and left off many of the levers as I didn't have the patience to add them in areas I could barely see. Only the exposed ones I added. The PE belts were added to the seat.

I painted the remaining interior parts including the radio compartment, tail wheel well and the radiator/oil cooler as per instructions. Once the paint was dry I added the fuselage halves together (CA glue on the exterior seams, Tamiya extra thin cement on the interior connections.) I sanded the seams away and made sure not to destroy as much of the fine detail as possible. I ended up replacing the top rivets using a ponce wheel. I had to go over the holes twice so that they would be deep enough. The panel lines were rescribed using a small thin razor saw.

The wings, intake and fuselage were glued together using Tamiya Extra thin cement except where the wings joined the fuselage (CA glue was used instead to eliminate any possible phantom seam.) The seam was quickly eliminated with some fine grit sandpaper and various grits of polishing cloths.

The resin wheels were masked and painted using the kit supplied masking aluminum hubs and german grey Tamiya XF-63 for the rubber. The rest of the landing gear was assembled and painted including the oleo scissors and doors.

Next I cleaned up, assembled and painted the prop with black Badger Stynylrez primer and the tips were masked off and painted flat white then flat yellow for the warning tips. After a quick inspection and repair of the seams, the plane and major parts were ready for painting.

The P-51Ds near the end of the war were bare metal. I masked off the cockpit with low tack tape and stuffed packing sponges Eduard used for some of their resin items into the wheel wells, intakes and exhausts. Once everything was secure, I sprayed on one coat of Badger Black Stynylrez primer. I would usually find those seams which weren't sanded and polished completely smooth. Once I polished away the oopsies and smoothed down the rough patches of the 1^st primer coat then I sprayed down the 2^nd primer coat. I would polish this down to about 4000/6000 grit using sanding/polishing cloths in preparation for the metallic paints.

Next I masked off the wingtips and rudder areas where the bright blue paint was going to go and sprayed down a coat of flat white. When the white paint was dry I then sprayed on the Gunze Bright Blue paint in two light coats. When it was dry I masked off the blue areas and then the black stripes on the edges of the bright blue areas as well as the anti-glare panel and a small section of the nose. The wing and aileron stripes didn't look so good so I masked the black sections off and sprayed on Gunze Gloss Black to make the black stripes darker.

I sprayed on Vallejo Metal Color (VMC) Aluminum for fuselage. I avoided spraying on thick which always causes paint runs. I kept on spraying light coats till the paint builds up to the metallic shade I want. When it was dry, I masked off the fuselage and sprayed VMC Dull Aluminum for the wings to represent the lacquered wings (however, I opted not to fill in most of the wing panel lines because I was lazy and didn't want to do even more work.) When this was dry, I removed the fuselage masking and then masked off various fuselage panels plus the gun bays on the wings and sprayed on VMC Dark Aluminum (around the engine compartment) and VMC Duraluminum for the darker areas of the rear fuselage and the gun bay access doors. I sprayed on Vallejo Air Steel for the rudder. Finally I sprayed on Vallejo Metallic Gloss in preparation for the decals.

The decals were put on without too much trouble. I didn't peel off the decal clear material as I didn't think it was worth the trouble. Most of the clear decal film disappears under a light application of decal solution.

I used a combo of Tamiya Panel line wash and watercolors for weathering. The watercolors unfortunately ran a bit when I sprayed on Vallejo Acrylic Gloss so I had to do some touchups and then I sprayed on a final coat of Vallejo Acrylic Gloss.

A number of small clear pieces were added to the model. I like the idea of the small lights being represented by actually small clear pieces, but the execution took much longer due to the small lights flying out of my tweezers. The clear pieces were secured with a drop of Tamiya extra thin cement then painted the appropriate clear color.

I added the painted ailerons, exhaust ramp, landing gear and landing gear doors as per the instructions and trying to get the correct angle on the landing gear. The painted prop was assembled and glued together. I used a drop of white glue to secure the prop to the shaft.

Next the painted canopy parts were added to the canopy hood. Next the entire assembly added to the model, but in the right position. The same for the gunsight parts and windscreen.

I sprayed the twin antennas with Tamiya Desert Yellow. After it dried, I dry brushed Model Master Acryl Burnt Sienna for the “wood pattern”. Next I sprayed on Tamiya clear orange for the final gloss as the final step to make the antennas look like wood (a bit out of scale to be honest.)

I used the Mark I eyeball to locate where to drill and position the antennas on the centerline spine. I was careful to avoid damaging the paint job (fortunately) when marking and drilling out the holes. Lastly, the tail wheel was glued in place and I finished my first Eduard P-51D build.

The Eduard P-51D lives up to its hype. Not as easy to build as the Airfix P-51D due to its fiddly nature and numerous tiny parts, but it is more accurate. I recommend the Eduard P-51D for those modelers of intermediate skill and above due to the number of tiny parts and assembly steps. Regardless, this kit was a fun build and my first ever Pacific Mustang.