The Millennium Falcon is a spacecraft in the fictional Star Wars universe commanded by smuggler Han Solo and his Wookiee first mate, Chewbacca. The highly modified YT-1300 light freighter first appears in Star Wars Episode IV: A New Hope (1977), and subsequently in Star Wars Episode V: The Empire Strikes Back (1980), Star Wars Episode VI: Return of the Jedi (1983) and in a cameo in Star Wars Episode III: Revenge of the Sith (2005). The Falcon also appears in a variety of Star Wars Expanded Universe materials, including books, comics, and games.

I'm not sure when this kit was first molded, but my copy was stamped 1988. It has been released in several versions, including lighted and a cutaway versions. Molded in light gray plastic, you can tell this was the lighted version as the kit still includes the battery box. The detail is good, but from what I read, it's not quite accurate. There was some flash on my kit, but nothing to serious. The biggest problem is the sprue attachments points, they are quite large. The top and bottom sections are molded as single pieces and both of mine were warped.

A sprue of clear parts is included and it is here that the kit suffers from having been lighted at one time. MPC includes a 2-part clear section for the aft engine and a template in the instructions, but they don't tell you what to do with it.

The instructions are typical MPC and easy to follow. They include some color callouts, but the majority of paint colors is left up to the modeler.

This version of the model depicts the Falcon as she appeared in Star Wars IV-A New Hope. In later movies the Falcon has 5 landing gear as opposed to just the 3 in this kit.

Since I wanted to paint the model as a whole as much as possible, I had to deviate from the instructions just a bit. The first step was to add the bulkheads to the lower section. The fit here was a bit dodgy and I had to do a bit of filling to get a decent fit. I also installed the upper and lower gun plates, leaving the blisters and guns until later. Once that was all dry, I painted everything. Next I painted the body inserts and installed them into the upper and lower sections. A good bond is needed here as once the sections are joined, if one comes loose, you cannot reattach it and it will rattle around the inside for eternity. I then painted and installed the engine exhaust, landing gear and boarding stairs. I left the stairs free to move so that they will always touch the ground.

The cockpit section posed a particular problem. As there was not really an interior to speak of, I decided to paint the clear parts. However, they are intended to been inserted into the nose section and then that attached to the main body. The fit is very poor on the cockpit "tube" and as MPC molded the top of the tube on the top body section, the instructions would have you attach the lower part of the tube to the body after the top and bottom are attached. Makes it kinda hard to repair the seams. I ended up gluing the tube together, with the nose cone, before I attached the two sections together. After filling, sanding and painting, I then inserted the clear part from the inside and the attached the top section to the bottom.

Gluing the top and bottom sections together required a lot of rubber-bands and several clamps. The fit is poor, but there is not a lot you can do about the seams without destroying all the detail. Installing the 2 side pods required some trimming to get a good fit.

Installing the guns and their blisters, gear doors and the large radar dish completed assembly.

Not much to do here as the entire main body is painted gray. After looking on the 'Net at various builds, I decided to go with MM Light Ghost Gray. I painted everything except the landing gear. I chose to paint those flat white. The engine vents on the rear deck were painted MM Flat Black. Using the Fine Molds as reference, I painted various panels with MM Rust, Intermediate Blue and Gunship Gray.

As this was a build for my daughters future husband, who is not a model builder just a Star Wars nut, I chose not to apply any weathering to the model.

Not a particularly difficult build, it does have it's ups and downs. However, I'm sure anyone with a few models under their belt can handle this. Anyone who is a Star Wars fan should have one of these in their collection.

I'm not real sure of my color choices, but seeing how it's a Sci-Fi model, I'm sure the actual color is debatable.

Fine Molds instructions for color details

Wikipedia for the history

Photos off the 'Net

Mark Hiott

December 2012