The cockpit comprises only two resin parts, a complete floor with seat (belts and harnesses molded on seat), control stick, and rudder controls already molded and an instrument panel. No sidewall detail is on the rather thick injected plastic fuselage halves, but truth be known, not much could be seen in the cockpit opening. I scratch built the PV-1 gunsight from white and clear styrene sheet and fine wire. It was painted semi-gloss black and set aside for final assembly.

All cockpit interior pieces were painted in medium gray, with exception of the instrument panel, which was paint semi-gloss black. The belts and harnesses were bushed dirty white, with the buckles pick out in bright aluminum. The control loop handle was painted in flat black. An ink wash was given in all recesses. The instrument gauges were first given a drop of white and followed by the application of Reheat Models instrument panel decals. The headrest was painted leather. It was a simple easy modeling task and the fuselage halves can be cemented right away, with the two cockpit assemblies attached after seam clean up. Nice going Pavla.

No engine was included in the kit and the instructions would have one attach the resin inner slat cover to the cowling in the closed position. That would not do and I had a spare Engine 'n' Things resin Shvetsov M-62, so why not use it. All I had to do to adapt the engine was to drill the cooling slat and cowling with the proper sized hole to accept the engine tube front. I didn't even have to cut out any of the resin cowling or sand away any of the engine cylinder ends. It was like the engine was made for the kit. The engine was first painted engine gray, the cylinders picked out in oxidized aluminum, and the push rods painted black. A clear gloss was applied and black washes were done after all paint had dried. I lastly brushed a little clear flat to the cylinders.

The cowling piece is resin and it is perhaps the worst molded piece in the kit. Lots of pinholes and raised dust specks, poorly molded intake orifices, and almost indistinguishable gun barrels. I cut away the gun barrels and replaced them with sections from a 25-gauge hypodermic needle. Using the Dremel tool and an engraving bit, I cleaned out the intakes a little, but had to keep that to a minimum. I filled all the pinholes with Dupont 30S auto primer, as I find it works better that super glue. The cowling was lastly sanded, but it still is the one drawback to this kit.

The exterior was nicely molded, but the recesses were a bit shallow for my liking. I rescribed all recessed lines a little deeper to prevent any sand through. The entire kit was a snap to assemble, I only had to apply filler to the lower wing/fuselage mount and even here I only used Krystal Kleer, which is a very god way to achieve a smooth filling without sanding.

The gear bays were painted medium gray and the gear struts graphite. I had to scratch build the retraction arm from styrene rod and it too was painted graphite. The wheels were painted RLM 66 and the tires brushed in tire black. The wheel centers received a coat of semi-gloss clear. The rear wheel was cut from the fuselage and a new one build from a Waldron-punched disk of styrene. A mounting slot was first drilled and then cleaned up with a Dremel motor tools and an engraving cutting bit. The gear door rods were done with fine wire painted black.

A set of resin FAB-250 bombs are included with the kit, but they are very poorly molded and also too long. I tossed them into the spares box, but doubt I shall ever use them

If someone knows what the tiny device on the vertical tail is, I would appreciate it. I replicated it on the model from the actual photo, but I have no idea as to its function. The starboard Venturi tube was scratch-built from 0.025-inch styrene rod and fine wire for the attachment. The front and rear were lightly drilled to show an opening. It was painted semi-gloss black and set aside for final assembly.

Notice I didn't say decaling, because there are none if one is building the aircraft before it's acceptance in the VVS. The kit gives one some nice looking Propagtem decals, but these were for the tractor green over light blue scheme give to the I-207/3 once in VVS service. Overall, the production prototype was paint a light gray, which matched very closely to RLM 76. Therefore, the entire model was painted RLM 76. A clear gloss was applied for ink washes in the control recesses. The model was lastly finished in a coat of clear flat and wing navigation lights applied to the upper and lower surfaces of the upper wing using Waldron-punched disks of Bare-metal foil, Krystal Kleer, and clear red and clear green paint where appropriate. The fuselage to wing rod bracing were done using 34-gauge wire and the cabane cross bracing done with 0.025 wire. All rods were painted black before attachment.

Caz Dalton

If you would like your product reviewed fairly and quickly, please contact the editor or see other details in the Note to Contributors.

Back to Main Page

Back to Reviews Page2020