When dealing with resin parts, the first thing one does is to clean them with warm, not hot, soapy water to remove any mold release. This mold release is an oily material sprayed into a resin mold to keep the resin from sticking to it. If you don't clean it off, you may easily have trouble getting paint to stick to it.

The next step is to start removing the resin bits from the blocks. The only safety equipment needed is a dust mask to keep you from breathing in the resin dust. A respirator is even better. Lay out all the resin bits to make sure that nothing is missing or broken.

There are two ways to remove resin parts and it really depends of the thickness of the attachment as well as the shape of the parts. For thin attachments, a hobby knife is usually good enough. You just scribe at the join until it is free. For most other parts a razor saw is what is needed. There are various types of saw, but the ones I like are those that fit into an knife handle. Just easier to use. Do beware when sawing as flesh is much easier to saw through than resin. You also don't want to hold resin parts with a death grip as some of the larger ones (like the cockpit tub) can be snapped with too much pressure.

So lets start removing some resin block. I started with the wheels. Using the razor saw, start sawing at the attachment point under the wheels. It is a good idea to leave a sliver of resin attached to the wheels. This is to prevent you from sawing them off at a weird angle. It is much easier to gently sand away the thin ribbon of resin than to try to replace a chunk that you have accidentally gouged out of a part. Trust me, few can actually saw level! Now on to some of the other parts.

The sidewalls of the cockpit will need to be removed a bit differently than using a saw. Thanks to the fact that they are curved on the bottom, using a saw really isn't the best way to cut these parts. The attachment of the sides to the resin block is also a lot thinner than with other pieces so scribing the join line with a sharp hobby knife blade is the best way. Just lay the part down on a relatively hard surface (I use a thick rubber mat), and gently scribe the part several times. Applying too much pressure could cause the part to crack, so take it easy. It took about 20-25 passes to cleanly separate the parts. Then you can just sand the underside to make it smooth.

Now that we have that taken care of, it was time to remove the instrument panel. True Details was nice enough to supply panels for both the P-40N and the earlier models. For the P-40E, we need the panel on the outside of the block. Now instrument panels require a slightly different approach to removal. For these, one needs to saw flush with the back of the panel. Not really difficult as the resin backing doesn't go all the way to the top of the panel. Just saw away at it carefully and try to keep things flat as you don't want to accidentally saw the panel in half (been there; done that!). 

As you get near the bottom of the panel, stop and saw the bottom of the panel, but no all the way through. You do this for a couple of reasons. One is to have a nice flat cut. The other is that there is often some extra lumps of resin in the underside sections of these panels and this is the easiest way to cut them out. Then go back and finish at the back of the panel. In just a few moments you will have the panel clear and ready to paint/install. Any unevenness in the back can be gently sanded smooth.  Leave the control stick and gun sight on the resin block until just before you need it. These parts are easily lost.

The next thing I did was to test fit the cockpit into the fuselage halves. It seems as if it will fit without removing any of the interior pins. I next tried to fit the bottom of the wing on. No go. This meant that I had to remove the resin block from the bottom of the cockpit tub. Sometimes you can get away with just trimming these parts, but not in this case as the clearances won't allow it. With a 'U' shaped piece such as the cockpit tub, it is quite easy to apply too much pressure to it while holding it. The result is that you break it in half. Using just enough pressure to hold it securely, but without having a 'death grip' on it, saw away until the resin block comes free. Then test fit it again to makes sure you have enough room.

Turning to the rest of the kit, it is time to glue together some subassemblies and to prep some of the other parts. First of all, the fuselage. The 'thingie' that is supposed to be the gunsight needs to be removed. Once you cut it off, make sure that you notch the area like the opposite fuselage half so the new gunsight will fit. Actually, it wouldn't be a bad idea to make each notch just a teeny bit larger as the resin sight is a bit wider.

Now you can glue the radiator splitter to the radiator, the wings together (your choice if you want the gun camera attached. If so drill out the hole for it), and your choice of bomb or drop tank. I chose the drop tank. Once the halves are glued together, glue in the supports and test fit them in the holes in the underside of the wing to make sure they will dry properly. This is because we'll have to fill in the gaps where the braces attach to the tank (or bomb). When dry, they are puttied and then sanded smooth.

Give those a bit of time to dry and start on some of the resin assemblies. First of all cut off the seat and stick and glue those to the cockpit tub. Then cut off the gunsight and glue it to the instrument panel. Take all of these parts to the paint shop and paint them. The interior gets a coat of US Interior green while the instrument panel gets a nice matte black. When done painting the main colors, follow the painting guide that comes with the interior to do all the little bits and pieces. This will take a couple of days to paint everything and give the paint time to dry. 

When everything is dry, give it a nice wash. I use Rustall black wash as it doesn't really flood things with black and is water based so I can wash it off before it dries. Doesn't harm already dried paint, either. With that done, I take some steel (or aluminum) Metallizer and do the drybrush thing to all the interior parts, being very careful not to overdo it or knock something adrift.

With that done, the instrument panel is glued to the fuselage, the radiator intake is glued to the nose of the fuselage and the sidewalls are glued to the interior, but only on the bottom. This way the sides can be gently squeezed when installed in the fuselage and will therefore fit snugly against the sides of the fuselage without gluing them.

On to some more gluing. The cockpit will fit from the underside without any real traumas. That being the case, the fuselage halves were glued together. This does two things. It makes sure that the instrument panel was properly seated (it wasn't so I pulled it out) and it makes it much easier to sand the seam that runs through the padded head rest. Not having any interior to get in the way really helps.

With the fuselage and wings together, there was some filler that needed application. When checking for seams to fill, I first try to remove as many as possible by just sanding alone. Sometimes they are shallow and that will work. The trick is to make sure that you don't sand a flat spot on a rounded surface or sand a wide groove in things. This last one is a particular hazard when doing wing roots and with softer plastic (like in short run kits) it happens quite easily. On the underside of the wings, there is a join line that needs filled as the flaps are a single piece. Part of the flap is molded on the underside of the fuselage. 

Now would be a good time to take your #79 drill bit and do the gun ports and start on the exhaust stubs if you wished to drill those out. It does add quite a bit to the finished product, but can also be difficult to do properly. I have found that starting the hole with the tip of a very sharp pointed xacto blade helps a great deal. This is also the time where I add the horizontal stabilizers. Doing it now and making sure they are square goes a long way to helping to make sure that the wings go on properly as you have a good reference in the back.

Once the tailplanes were solidly on and the various sanding had been done where needed, it was time to reinstall the instrument panel and then put in the interior. I used superglue for these as I wanted a quick hold once the parts were in place. Both fit well with no real hassles. The side panels stuck up a bit above the sides of the cockpit, but have not yet been trimmed as they may well be hidden by the closed canopy frame.

The wing was then installed and it was obvious that there was a bit of a problem. The wings were just as straight as could be from side to side. 'So what's the problem?', you say. Well, the P-40 wings have a bit of dihedral and are not supposed to be flat. Fixing this isn't really that easy as the fuselage and the wings are well braced. My only real choice was to start sanding away at the fuselage wing root. Not a job that I really enjoyed doing as I just cannot do these kinds of thing right. 

Not sure what caused the flatness of the wings, but thinking back on things, I have a sneaking suspicion that it has to do with the resin interior. I did not remove any of the old interior locating pins as they didn't seem to be in the way. It could be that they caused the fuselage to be wider and so caused the glitch with the wing dihedral. I have not had this problem with any stock kits so it makes sense. Live and learn. Anyway, the damage had been done so the fuselage was sanded, the wings attached, and the filler used to cover up my goof.

The model was then flipped over and the cowl flaps glued in place. Next step was to do some touch up painting in the cockpit and to get the canopy ready to install. Since the area under the 'quarter windows' was to be fuselage color, those wouldn't be put in until near the very end. The canopy was masked and then glued in place. The canopy is very clear and all of the interior bits can be seen rather easily. It also covered up the fact that the resin sidewalls were a bit too high so won't be noticed. Once that was accomplished, the prop spinner and landing gear were removed from the sprues as was the prop in preparation for painting.

For a P-40E in SWPA, we are talking about your standard OD or Medium Green uppers with Neutral Grey lower surfaces. Nothing really fancy or complicated unless you want to do a plane that was originally going to the RAF. Those will have a two-color upper surface camo scheme similar to what the Flying Tigers P-40B/C's wore. Well, I chose an easy one. This 8 FS P-40E was to be Dark Earth on the upper surfaces and Neutral Grey undersides. Now I didn't have any Dark Earth and frankly, I have my doubts about a single upper color being an RAF one, so chose a faded Olive Drab. They are pretty close matches. 

The underside was first painted and then masked when dry. The upper color came next. I used Aeromaster Enamels for both of these colors. When those colors were completely dry (like a few days), I brought the kit back to the work bench and did some hand painting. Specifically the chromate wheel wells and gear door interiors. Then the landing gear was added and the plane taken back for a coat of Future clear gloss acrylic in preparation for the decals.

For decals I used Superscale sheet 72-675 for 49 FG P-40Es. The plane used was Lt. Eisenburg's 'DollyE'.  This plane is unusual in having no blue surround to the fuselage insignia. It also has a large Pegasus on the fuselage to add some interest. The Superscale decals worked just fine. Two minor things. First of all the name 'DollyE' wasn't on the sheet. the carrier film was there, but no name! I also didn't use the decal sheet's wing insignia. The insignia on this sheet just don't seem right to me so I dug out an ancient Scalemaster sheet for replacements. These worked well, though they took forever to come off the sheet (guess age will do that to you!). I applied a few stencils just to break up the monotony of the scheme. I seriously doubt if these stencils were actually on these planes as it seems that some were repainted at Australian Depots. Usually stencils would have become a casualty of the repaint. I applied Solvaset to force the decals into submission and it worked as advertised.

WIth the decals now on, I could attend to some more bits and pieces. These included the attachment of the resin wheels. These had previously been painted and drilled out so were just slipped on the axle stubs along with some superglue and left alone for a bit while the glue dried. Next the prop and spinner assembly was glued together. Finally, the gear doors were cut apart and glued in place. This is probably the weakest part of the kit next to the instructions. I never seem to be able to perfectly cut these doors. Haven't seen the Academy E but I do hope that these doors are precut.

The model was then given a coat of clear flat using my age-old mixture of Future and Tamiya flat-base. Then the pastels were brought out for the engine exhaust and the gun stains. I also used it to highlight some panel lines and wiped much of it away. Left the kit slightly dirty looking. The masking was removed from the canopy and the quarter windows were glued in using non-fogging superglue. Finally, the drop tank was glued in place. Then the hard part; attaching the radio antenna. 

You really cannot go wrong with any of the second generation Hasegawa single-engine prop kits. They all fit reasonably well with minimal hassles and can be improved upon with inexpensive aftermarket resin bits. For those who aren't as glacial a builder as I am the kits can be completed competently in about a week or even less. A great kit for even the newest builders.

June 2001

Copyright ModelingMadness.com. All rights reserved. No reproduction in part or in whole without express permission from the editor.

Review kit courtesy of me and my wallet!

If you would like your product reviewed fairly and fairly quickly , please contact the editor or see other details in the Note to Contributors.

Back to Main Page

Back to Reviews Page 2016