As has become the norm for me, I'll leave it to the preview to provide all the needed info about the kit. 

 If you recall from the preview, I ended up stating that the kit should be a snap to build. The sound you hear in the background is me, munching on those words. This kit is a case of 'looks great in the box, doesn't build as it looks'. Not to say that it is a bad kit and is a total pain to build. That isn't the case at all. It is just that you need to treat it like a well done short run kit. And frankly, that is what these early Fine Mold kits were.

Shall we start with the interior?  Very well. The first thing I did was to go over the kit instructions and glue together all the interior bits that were to be painted the same color. That included most of them. There are a number of very fine bits that fit in the cockpit. These are rather small and can easily be lost. The instructions are quite a help in determining the proper placement of most of them, though there will be a bit or two that you'll have to glue in place based on a best guess. Once all the parts to be painted Mitsubishi Interior Green were assembled, the cockpit and surrounding interior were painted in that color using my slowly diminishing Aeromaster Acrylic paint. When dry, some of the parts that needed other colors, like black or wood were hand painted. 

The interior was then placed into the lower fuselage and the fuselage halves glued together. No need for nose weight on this kit. The seat, back plate, control stick and some mysterious looking bottles were left off until near the end of construction.  When I glued together the fuselage halves, I also glued the wings, tail section and the small tail wheel assembly. Fit of these rated from OK to not the best, especially the tail section. 

I then glued the tail section to the upper fuselage. Yikes! Talk about Gap City. Not a good fit at all. With a sigh, I broke out the filler and slathered it on the offending gaps. Not only that, but the tail was slightly smaller in diameter than the back of the fuselage so filler was needed to fair that in. After the first coat of filler, the right wing was glued on. Gaps here as well. I guess you notice a trend. Nothing that can't be fixed by filler, but a pain, nonetheless. After several sessions with the Acryl-Blue filler, the main parts of the aircraft were complete. 

The next step was to finish off the cockpit. This involved attaching a pipe that ran behind the seat, then the three bottles. Fit was rather good here. The bottles were painted flat black with an aluminum valve section. Then the seat with the armor plating was installed. I should say that I tried to install it. The opening in the floor for the tab on the plate was smaller than the tab on the plate. I trimmed it a bit and the seat fit well. 

Next the canopy sections were installed. The aft section fit quite well and was glued in place. Once dry the transparencies were masked off. The forward part was masked using Tamiya tape. The radio mast hole was blocked with a small section of tape from the inside and the canopy tacked in place for painting. 

This kit has separate leading edge slots, which is much more realistic than a few indentations. These were glued in place. Fit here was fair, but not perfect. However, these late war aircraft were usually lacking in proper quality assurance and fit so I don't think it will be a problem. The tail wheel segment  and pitot tube were glued in place and the kit was ready for paint.

First thing I did was to construct the small wheeled dolly. This is basically a gloss black axle assembly with aluminum wheels attached. The mechanism that extends and retracts the skid is made of three articulating assemblies. Each of these is made of two parts. They are quite fragile and I managed to break a couple of them while gluing them together. They were then painted aluminum. There is a small attachment piece that fits into the skid and later is what hooks the skid to the dolly. WHen the dolly was dry, it was glued to the bottom of the skid (there are some small nubbins for alignment) and the two connection pieces are glued from the dolly to the attachment on the inside of the skid.

The skid well itself was touched up and the three retraction/extention assemblies were glued into the well. When dry, the skid with dolly was glued to them. I used superglue for a number of these bits and it holds quite well.

The canopy was unmasked and naturally, there was a bit of bleed-under on the forwardmost section. A bit of work with a toothpick took care of the excess paint. Any glitches in the paint were touched up and the final bits added. These consisted of the radio mast and the canopy brace. The canopy sits on this brace when open. Were the kit to be built canopy closed, this brace would fold down across the upper section of the 'dash'. This is just like in many cars with the hood brace. No need to paint any formation lights as the Shusui didn't have any!

Back to Main Page

Back to Reviews Page2015