To take a look at what is in the box and to get a bit of background, please follow this link.

 Ever get one of those models where you immediately want to start building it? Well, for me, this is one of those kits. I just don't know why, but it is. If you read the preview, (see link above), then you know that this is a short run kit. That means that the first steps you'll take are to clean up the parts you will be initially putting together. For this kit, that meant removing the rather large ejector stubs from the fuselage, wings and tailplanes. If you have a set of flush-cutting sprue clippers, it will make pretty quick work of these stubs. Then there will just be a small bit that needs sanded smooth.

Once those were removed, the sprue attachment points were sanded smooth as many of these are on the edges and if not removed, won't allow the pieces to be glued together. The rough edges were then sanded or scraped smooth on the wings, tailplanes, fuselage halves and the engine nacelle halves. Once done, the wings, tailplanes and engine nacelles were glued together and set aside to dry.

During this time, I started to cut the resin parts off their blocks. Take care with the cockpit as it is easy to break off some of the more delicate parts on the floor. I know this from experience. The two seats, instrument panel, lower bombardiers panel and control columns were carefully cut away. Take particular care with the control columns so as not to break the control wheels. Careful sawing and sanding will get these pieces off the blocks. Once those bits were all removed and cleaned up, they were glued into the cockpit. At this same time, a couple of radio panels was glued to the left interior wall. It was all then taken to the paint shop in preparation for painting.

The next parts to get my attention were the wings, tailplanes and engine nacelles. These had the edges sanded smooth and any seams filled with either Mr. Surfacer 500 or normal filler. 

Starting with the nacelles, the inserts for the forward portion of the wheel wells were cut from the resin blocks and attempts were made to install them. They needed to have the upper portions trimmed a bit as the parts as designed do not have the same angle on the upper section as in the nacelle. These were glued in with superglue as are all the resin bits.

Once the inserts were dry, I tried to install the nacelles on the wings. The upper section of the wing has a small nacelle part that is supposed to slot into the nacelles. It doesn't fit. The problem is that the plastic is too thick on the nacelles and the upper section of the nacelle is a bit too small in radius compared to the same bit on the upper wing. The result is that the upper glue join on the nacelle will undoubtedly split when you try to install it. Thinning the inside of the nacelle is a big help, but I had to result in using superglue to fill in the rather large gap that was there. No one ever said that short run kits were slap-together models. The nacelles were clamped to the wings to allow the glue to dry relatively gap free. After they had dried, a small amount of filler was needed for a few gaps. That was then sanded smooth and the small section of wing between the nacelle and fuselage was glued on. Why this was not included as part of the wing half I do not know. Anyway, the fit isn't the greatest, but it isn't anything beyond those who have reached this level of skill.

Turning back to the interior, all of the parts were painted with 'bamboo', a sort of yellowish green primer. There is no artifact of a Ki-21 around from which to get paint samples, so it could just as easily have been a dark green or even a grey green. Japanese interior colors is something that is a mystery to many of us! Anyway, once dry, the various parts had other bits picked out in various colors to add some interest. 

While this was drying, I went to put the small square transparency in the aft fuselage section. The instructions show it fitting from the inside. Well, if that is done, then there will be a very deep depressions from the outside until the clear bit is reached. Not very aerodynamic. The opening was enlarged with a square file until the transparency could be fit from the outside. It was then glued in place. The interior bits were then glue in place on the right side using superglue. The fuselage halves were held together during this operation to make sure everything was well aligned.

When that had dried, the other fuselage halves were glued together and clamped in place. The horizontal stabilizers were glued on to the back at this time as was the tail gun housing. The usual slathering of filler was added to the seams (it seems inevitable with these kits!).

Next is probably the biggest pain of the whole kit. The transparencies. One gets used to parts not quite fitting properly in these types of kit, but when it is the transparencies that are a bit off, fixing the problem is not as easy as just applying filler or sanding things down as often you'll destroy some of the clear parts doing this. Unfortunately, it is filler and a bit of sanding that are needed to correct the transparency problems with this kit. The biggest problem areas are the two underfuselage parts at the rear and the nose area. These each required some very careful filling and sanding to match up with the surrounding fuselage and even then some areas were not able to be properly treated. On the upper side, the main cockpit canopy is actually a bit narrower than the opening. This means that one side fits well while the other doesn't. Out comes the filler again for this and the front section. The center nose transparency looks like it will fit well enough after sanding, but it wasn't installed at this time.

The reason for not completing all the transparencies is the guns. You have to make up your mind if you want them and where you want them. There are six places that can have guns. Two in the lower transparency area, two in the aft section of the cockpit canopy, one in the nose and one in the aft transparency. All but the last location will need to have holes drilled to accept the guns. Needless to say, none will be installed in the lower transparency section or the cockpit. However, I'm not sure about the nose as of yet. There are no mounts or any other 'stuff' in any of these areas so it will look a bit bare having the guns mounted there. The kit provides four resin guns so you cannot put them in all available locales. Naturally, what I chose was to use only the one for the upper aft section. This consisted of a resin gun and flimsy resin mount that was painted black in preparation for gluing in place.

The nose transparency was glued on as best as possible and any jutting edges cleaned up. My attention then turned to the aft upper transparency. If doing the kitted version (as I did), you need to glue the blanking plate with the gunners seat into the underside of the transparency (which I did). Then you do a test fit to make sure it all fits (which it didn't). Yup, I had mounted the rear floor with fuel tank too far forward so the seat banged into it. The cure was to first try to cut the fuel tank off (you won't see it anyway). It decided to have the whole resin floor break loose. Hey, no problem, just lined things up and reglued the floor! In fact, I would heartily recommend not installing the rear floor until this stage as it is a MUCH easier time to do it and get it level! 

Once the floor was reinstalled, the aft transparency was test fit for the gun placement and then glued in. Then the transparency was test fit again. You will find as I did that the forward section of this canopy is not only too narrow, but too tall as well. (Sigh!). Well, you could clamp it in place and use pressure to spread things out, but you'd undoubtedly be rewarded with a loud CRACK as the canopy broke. I just glued mine in place and started sanding and filling! After that onerous job was done, the transparencies were properly masked off (a task that took several days and is not for the faint of heart) and the kit was ready for its first shot at painting.

There are kits that build well and then there are ones like this. Frankly, I know a number of modelers who'd have tossed the whole thing in the trash weeks ago, but I feel I need to finish everything I start. The construction hassles were nothing compared to the problems with paint, but now I know what not to do so I leave this build having learned and I guess that is what is important. I know it can be made into a super model as there was one at the IPMS Nationals and it was superbly done. Mine will be placed on the shelf of shame in the display case of the dead in the basement!