The major workhorse of the Luftwaffe fighter arm during the first part of WW2 was the Bf-109E. An improvement over earlier models with its Daimler-Benz DB601 engine in place of the older Junkers Jumo, the 109E was the aircraft most often met by the RAF during the battle of Britain. The versions most widely produced of the E were the E-3 and the E-4/7. The E-4/7 has protruding wing cannon barrels and a more square canopy than the E-3 version. The E-7 can a cap over the nose cannon producing a more streamlined prop spinner. The E-7 was also fitted with a centerline rack for a drop tank or bomb.

The E-4/7 was flown by a number of the early aces or 'experten' of the Luftwaffe including Galland, Molders, Priller and others. The E version soldiered on after being replaced by the more uptodate F model in training schools and by being sold off to other Axis allies.

Hasegawa has always gotten excellent mileage out of it's kits. Often by doing nothing more than supplying new box art and a new decal sheet. The Bf-109E series probably has made more use of this than any other Hasegawa kit. I know of at least ten different boxings of this kit, all with the same plastic inside. This one is for two Luftwaffe 'experten'. One is an E-7 from JG 5 flown by Gunter Scholz and is depicted on the boxtop. The other is an E-3/4 from JG 77 flown by Ludwig Froba. Unfortunately for me, the decal sheet managed to stick to the bottom of the box so tore when removing it. Not a real problem as I had planned on using aftermarket decals for this aircraft anyway. The kit decals look a bit transparent as I could easily see the blue backing under the white parts.

This kit is the modified 109E. The very earliest E models had some shape problems in the nose and rear fuselage. Those were marketed with the 'J' series boxes while the revised ones are all in 'JT' boxes. Typical of Hasegawa, the parts are very well molded in grey plastic with superb detail and engraved panel lines. There is a small fret of etched parts for the radiators and the canopy armor. I have never had any real success with the canopy armor, always managing to mess it up in some way or other.

In addition to the usual bits and pieces, one gets both the rounded and more square canopies, so you can do an E-3, E-4 or E-7 with this kit. If you like 109's like I do, buy a bunch of them when you see them on sale. Like the Tamiya or Hobbycraft 109E, this one comes with droppable flaps. It also has separate slats. The cockpit detail is good right from the box, but like most models, can be improved with an aftermarket cockpit set, same with the wheels, which are not flattened.

This kit is to be built as one of the Bf-109T prototypes; the 109v15. The 109T was designed to be used from the Graf Zepplin, Germany's first aircraft carrier. Due to a number of delays, the ship was launched, but never finished and never has a single aircraft take off or land on its deck. The 109Ts were then shorn of their aircraft carrier specific equipment and used in Norway and in local defense in the North Sea. Their longer wingspan and more powerful engines gave them good altitude performance and they were in use until late 1944 when the tired airframes were scrapped.

Hasegawa has recently released this kit yet again as a regular Bf-109T with resin detail parts for the longer wings and the new supercharger intake. I haven't seen the kit, but have been told that the resin bits are by Jaguar. Apparently missing from the Hasegawa kit are the carrier equipment such as catapult attachment points, tailhook, and holdbacks.  MPM produced this kit a few years ago, however it is limited run and the fit is not to Hasegawa standards 

Really wanting to do one of these, I purchased the Hawkeye Designs conversion set. A friend sent me a set of MPM decals for the 109T which include the version I want to do, so I have all I need for a nice 109T. Since I'm going to be putting in the conversion set, the equally superb Hawkeye Designs interior will be used as well as some True Details resin wheels. I have used the last items before with a 109D and have nothing but praise for them.

First order of business is to prepare the kit wings for the extended tips. They are cut, using a razor saw, at the spot indicated in the HD instruction sheet. Actually, I fudged a bit and cut them a bit log to make sure they wouldn't be too short then sanded them back. The HD set includes new longer ailerons and slats. At the same time, the two bulges under the wings were removed to make room for the catapult attachment brackets. Once that was done, the wing was assembled as per kit instructions.

Basically, that takes care of the cutting and hacking part of the conversion. Pretty simple, really as the cuts are along a panel line. Next was to get to work on the new resin cockpit. This set is truly super and really looks a bunch better than the stock cockpit. The basic bits were glued into place, not forgetting to use the kit forward bulkhead, and the whole cockpit was sprayed RLM 02 green-grey. Next, some seat belts were attached from a Reheat etched brass set. If I may hop up on the soapbox for a moment, I feel that these interior sets should either include etched brass belts or have them molded on the seat. The modeler shouldn't have to fork out another 10 or 12 dollars for a belt set.

While that was drying, the kit etched radiators were glued in place and the wing halves and fuselage halves glued together. Fit for these parts is good with only minimal filler needed. Next, one of the new resin wingtips was glued into place. I found that the panel lines are not exactly the same on the top and bottom of the wing so some additional sanding was needed to even things up. Then the wing tip was smothered in super glue, the tip lined up and then hit with accelerator. During this, I found that the wing tip was slightly less thick than the kit wing, so the kit wing was sanded down to smoothly match. 

The Hawkeye Designs kit gives you replacement slats and ailerons. The slat was slightly too long so sanded down a bit. Then it was glued onto the leading edge. There was a rather large gap on the bottom of the slat that was filled with superglue and then sanded. Any pits were filled and sanded smooth. As a note, none of the Bf-109Ts (and this included the prototypes) had functional wing slats. Because of the longer wings, when they deployed they really upset the stability of the aircraft. Therefore, the slats were all bolted into place in the up position. As you might expect, though the parts fit ok, I had the usual problems as I always do with any conversion set so it wasn't exactly a trouble free process!

Then it was time to put some of the fuselage bits together. The instrument panel was superglued into place and the cockpit was then installed. YIKES!  It was not even. Somehow, I missed the fact that the aft bulkhead was warped so getting the cockpit to fit in the fuselage took some careful tweaking and lots of superglue. Finally, it was installed to my satisfaction and looks pretty good. Then it was time to glue the wings on. Dry fitting it, I noticed that the front was a bit too tall, not letting the upper wings match up to the root. A tiny bit of sanding on the front fuselage attachment point took care of that. The rear part gave me fits, until I finally got it to fit in there level. At that time, the wing was then glued to the fuselage and set aside to dry.

Once dry the filler was sanded down and smoothed into the surrounding surfaces. Then I looked for the nose guns. Somehow, they had disappeared and no amount of searching turned them up. Fortunately, I have a rather full spares box for the 109 and was able to scrounge some from there. These were glued in place and the cowling was glued onto the nose of the aircraft. During all this handling on of the resin wing tips had broken loose so was cleaned up and reattached. The tailplanes were then glued in place without the braces to facilitate painting. The flaps were glued in the up position and the ailerons were then glued at a bit of an angle to give it some interest. The balances were left till the last step to prevent them from being broken off and lost.

Next the gunsight was installed in the interior and the clear bits glued in place. Then the forward resin catapult attachments were glued in place as I doubt I would be knocking these off. I used the older of the two canopies as is fitting for an early 109E. They were then masked with low tack tape and Bare Metal Foil. The wheel wells filled with tissue and it was off to the paint shop for the first round of painting.