ZTS/Mikro72
1/72 RWD-5
KIT #: |
S-05 |
PRICE: |
$3.00 or so when new |
DECALS: |
Two registration numbers |
REVIEWER: |
Scott Van Aken |
NOTES: |
|
The RWD 5 was constructed by the RWD team of Stanisław Rogalski, Stanisław
Wigura and Jerzy Drzewiecki (their designs were named RWD after their initial
letters). It was a further development of earlier RWD aircraft series (RWD 1,
RWD 2, RWD 3 and RWD 7), especially of its direct predecessor, the RWD 4. It
shared the same wing shape and construction, while the fuselage was totally new,
constructed of steel frame, unlike its wooden predecessors. The fuselage had a
modern shape and a closed canopy with panoramic windows (earlier models had
atypical fish-shaped fuselages with no direct forward view from the pilot's
seat).
The first prototype (registration SP-AGJ) was flown on 7 August 1931 by its
designer Jerzy Drzewiecki. It was built in new workshops of Warsaw University of
Technology near Okęcie airport, from 1933 converted to Doświadczalne
Warsztaty Lotnicze (DWL) company.
After successes of the prototype in air competitions, a small-scale series
production was set up, mostly for the Polish Aero Club. Series aircraft had
improved landing gear. Two were built in 1932 (registration SP-AJA and AJB),
five in 1933 (including the single-seater RWD 5bis), eleven in 1934 (including
one in Aero Club workshops in Lublin) and one more in 1937 (SP-BGX), for a total
of 20 aircraft. In 1932, the RWD 5 was shown at the International Air Show in
Paris. The RWD-5bis gained fame for flying the South Atlantic from Senegal to
Brazil non-stop and setting a distance record for small light aircraft.
This
is a kit I've had in the collection for so long that I don't recall where I
got it. The kit is definitely from the Cold War era as the box and
instructions are in a pretty cheap paper/cardboard, the decals have so much
carrier that they are basically on a solid sheet and the plastic is in a
rather bright turquoise color. The two colored and one clear sprue are
pretty nicely molded with the fabric parts of the airframe having a rather
rough texture. While the clear bits are not all that transparent, for
something like this, they are good enough. The only real flash is on the
long exhaust and there are some ejector and sink marks, but nothing really
horrible.
One is able to build either the RWD-5 or RWD-5bis. The latter is the single
seat version and that is how the fuselage is molded. To do the more common
standard plane, one has to remove sections of plastic from the sides. This
area is clearly marked and one has separate side windows for each version.
The interior consists of a floor with room for a control stick and two
seats. If doing the bis version, there is an additional fuel tank that goes
in place of the rear seat.
The upper wing is two pieces with the lower section being an insert that
covers about half the lower wing. This means that the upper and lower outer
wing pieces are a single molding. Same with the fin/rudder and horizontal
stabs. Remarkably, there are no wing struts. The landing gear is probably
the most complex part of the kit. This consists of the main inner struts
which are a single mold along with the lower fuselage in that area. Two
outer struts then attach to the wheel pants. These items are in left and
right halves with the wheels molded in place. Not all these planes had the
pants so you'll have to dig through your spares box for wheels. A tail skid
is on the rear with the three transparency pieces fitting in after most of
themodel is built and before the wing is installed.
Instructions are a single folded sheet with history and painting on one side
and construction on the other. There are three options available. One is
SP-AJU as either a single or two seat plane in overall silver. The other is
a two seat plane, SP-ARP with a lot of red trim on the fuselage. I'm not
sure how viable the decals are after what has to be 25-30 years, but unless
you want to copy them and make new ones, you'll have to test some you won't
use. No interior color info is provided so you are on your own in this
regard.
Though this may be an old kit, it is nicely molded and I have to admit that
injected plastic kits of Polish interwar light planes are few and far between.
https://en.wikipedia.org/wiki/RWD_5
June 2016
Copyright ModelingMadness.com
Thanks to me for picking this one up.
If you would like your product reviewed fairly and quickly, please
contact the editor
or see other details in the
Note to
Contributors.
Back to the Main Page
Back to the Review
Index Page
Back to the Previews Index Page