As with all resin kits, construction starts with clean-up. Also typical of figure kits, painting is a constant process. For that reason, I have included it in with the construction steps. Back to clean-up. In this case, it meant sanding off as much of the mold seams as possible and then giving the parts a nice wash in luke-warm water with plenty of detergent. It also meant removing the small mold blocks that were on the parts. Once that is done, the next thing to do is to give the parts a coat of primer. This does two things. It shows up any areas missed and it also preps the parts for painting. 

As you can imagine, a number of small pinholes appeared that were not there before the primer was applied. I also spotted some other seams that were missed earlier. In order to make it easier to paint the large body of the figure, I drilled some holes in the heels of the figure. Into these holes were inserted some short lengths of paper clip. Similar holes were made in a spare base that I had. This will allow me to paint the entire figure as construction goes along. The pins were not glued in any way as I knew that I'd need to handle the figure quite a bit during construction and the base would just get in the way.

Once that was done, the pinholes and other glitches were filled with Mr. Surfacer 500. In addition tothe pinholes, there were some rather large holes on the inside of the feet and ankles that needed several applications. This stretched out preparation to over a week as I gave each application of Mr. Surfacer and primer a good day to dry.

Finally, I was at a point where I could start cementing parts together.

The kit has long, flowing hair. This assembly is in three parts and attaches to the back of the head when done. There are some guide pins and slots to help with assembly. I glued the left main section of hair to the head assembly and then glued the other two hair sections together. The two lone sections fit OK, but there was a step and gap that needed filled. Again, several days were needed to get this right.

Backat the body of the kit, the right arm was glued in place. This had some chips taken out of the resin at the attachment point so also needed several applications of filler to smooth out. The end result looks like something  you'd see in a museum in Athens!

Once that arm was properly filled and smoothed out. the left arm was attached. This side did not fit as well so required more work with filler and sandpaper to get an acceptable fit. The end result was getting closer to being a complete figure. The primer that I used was thinner than I would have liked, but I guess that is the point. It took multiple applications to cover the darker filler that I had used. 

After I had applied enough primer to get it ready for painting, I applied several coats of paint using Badger Accuflex acrylic paint. I used the 'suntanned flesh' color. Once done, I took a look at the result and didn't like it. Too dark for my tastes. There were also some areas that had run and a few other glitches. 

Some fix-it work, mostly with fine grades of sandpaper, was done to the body to take care of the rough spots and oversprays. Then a normal flesh color, also Badger Accuflex, was sprayed in many very light coats. This seemed to do the trick in terms of lightening up the flesh tone and getting it more to what I was looking for. 

While all of that sat around and cured for a while, I went to work on the other parts of the kit. Specifically the sword and the hair. Try as I might, I couldn't get the sword to be completely straight. A problem with these long, skinny resin bits. Wasn't sure what colors the sword would be painted in, but I did know that it would be a metallic of some sort for most of it. To that end, the sword was painted gloss black over the white primer coat. I then painted the sword using greenish metallic color from Alclad II. The effect is quite interesting. This was then masked off and the rest of the sword painted with dark aluminum, another Alclad II color. The two 'jewels' in the handle were painted clear red and green using Tamiya paint. The only color left to do is whatever I decide to paint the handle in, probably a leather color.

The figure's hair is to be a grey color in keeping with the color card that came with it. That is not a problem for a military modeler as I have lots of greys. I chose Testors Model Master Canadian Voodoo Grey enamel as the base color for the hair. It took several sessions to finally get all of the hair sprayed in that particular color. The head was masked with Tamiya tape to prevent any grey overspray.

Once the hair was painted, the face got a bit of attention with the whites of the eyes painted it. Then the irises were painted, this time using a semi-transparent orange color. The pupils were done in black . Next the eyebrows were painted in a dark brown and the area under the eyelid was done in black using a drafting pen. After that had dried, the two forward sections of hair were attached using superglue. There is a bit of a gap in the forward section and it was filled, again using superglue. The hair was touched up using the Voodoo grey.

Now I've looked at a lot of figures, and they are generally overly accentuated with various washes. I know this is considered the norm, but I really don't like the effect so tend to not do the wash thing. Instead, I mixed some of the normal color with some white and sprayed that lightened color on the areas that would normal take a highlight. This includes the cheeks, forehead, tops of shoulders, breasts and buttocks as well as knees, and other upper surface areas. The parts that may be in shadowed was painted with suntanned flesh, also a Badger color. The shading is subtle and more of what I like. The areas in between the toes as well as the areas between the arm and body and the bellybutton were darkened using a Rapidograph pen

The next step was to attach the head to the neck. This was the worst fitting part of the model. No matter how I tried, I just couldn't get a good fit. Not sure just exactly how to go about correcting that other than to attach the head to the neck prior to putting on the back sections of hair. Then those would probably not fit well and need fussing with. The final back section of hair was glued in place and the fit here was not as good as I'd have liked, mainly because the head had been glued on and the hair interfered with the body.

Last parts to be glued on were the sections of hair just below the ears. These needed some ribbons on them. I went to a place that sells ribbons and bought some red ones that I could cut. These were trimmed into small sections and tied onto the appropriate areas on the figure. I'll have to find something more flexible next time as I found the one I bought to be too stiff. These sections were glued in place. Then the resin section was glued in place with the ribbon covering much of the join. The sword was a real tricky part of the kit. It seemed more like an afterthought as anything else. There seemed to be no proper way to attach it to the hands. Finally I ended up just placing in the figure's hands in a pose that seemed to match what was on the artwork that came in the box. 

This was my first large scale resin figure, and one that has alot of skin. Despite my apprehension about painting all of that, the kit went alot better than I thought it would. Since then I have started on several other resin figures and I can tell you that they are not all made the same. Some of them are downright terrible in terms of the quality of the molding. However, these were all cheapie kits selling for around $20-30. I guess that one gets for what one pays for.

If you are looking for a change from the norm and can handle the painting that is required, I can heartily recommend one of these kits.

Review kit courtesy of me and my wallet. Thanks to Almer Awards for the name tag and to Kevin Powers for the base.

August 2001

Copyright ModelingMadness.com. All rights reserved.

If you would like your product reviewed fairly and fairly quickly, please contact the editor or see other details in the Note to Contributors.

Back to Main Page

Back to Reviews Page 2019